mailwhite01

Fiat 500 Replacement Key Fob If your remote key fob has stopped working, it may be time to replace the battery. If you replace the battery and it still doesn't work it could be a problem elsewhere. At United Locksmith, we specialize in the creation of new keys for old cars. We have all the tools and accessories needed for this service. Dead Coin Battery The most frequent reason why your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The key fob is equipped with an internal battery called a coin cell that will drain quickly when it isn't being utilized frequently enough. If your remote started to show signs of weakening like a loss of range, and then stopped working completely the battery could be dead. The battery inside the key fob is held in place by metal retaining clips. If the clips aren't tight, they can cause problems with the contact, which can stop the remote from receiving power. With a small flathead screwdriver, break the clip that holds the retaining pin open to take out the battery and insert a new one. Make sure that the battery you choose to use has the same voltage, size and specifications as the original. The exposure to water can cause the key fob to become corroded or damaged. Even a brief bath in warm, soapy water can cause damage to the chip. It is recommended to keep your key fob in a dry location. Water Damage Water damage may be the cause of your key fob's inability to function properly. Key fobs come with rubber seals to protect them from being damaged by rain or splashes of water, but it is very important to keep your keys out of the ocean, pool, and washing machine! The key fob is equipped with an electronic chip inside it that sends a signal car's immobilizer system. The chip allows the 500 to be locked and started. If it gets wet it won't work. Try cleaning your key fob's internal electronics with isopropyl Alcohol or an electronic cleaner to determine whether they're still working. However, it's best to get a replacement from a dealer instead of trying to fix the key fob that has been submerged by salt water. While a replacement fob can cost you a little bit of money, it is far less expensive than paying for your Fiat 500 to be towed to a dealership and fixed! You can also do it yourself with some simple steps. Be sure to have the correct type of battery before attempting to open your key fob. This task is much simpler than it appears, and there are step-by-step instructions online for almost any key fob in your car. Faulty Chip The chip in the key fob communicates with the car's immobiliser system to ensure your car is only able to start when the correct key is inserted. If the chip is damaged or corrupted it won't allow your car to start no matter what you do. A faulty chip can occur due to a variety of reasons, but the most common reason is water damage or the battery being dead. Regardless of the reason, it is a good idea to leave the work to a locksmith since they will be able to replace the chip fast and at a reasonable cost. If your key fob ceases to function after exposure to clean water from the tap or rain, take off the battery and wipe down the electronic component with a paper towel to ensure it's completely dry before putting it back into. If the key fob will not function, there's the possibility that it's malfunctioning components and need to be replaced. Some people will go to their dealer when in need of an entirely new Fiat key fob, but this is a costly option. United Locksmith is the best option if you need your Fiat key fob repaired at a reasonable price. We have the equipment and know-how to repair your Fiat fob in a professional and timely way. Faulty Receiver Module Fiat key fobs send a signal up 50 feet away to the vehicle, which allows it to unlock and close the doors (and start the vehicle for vehicles with automatic transmissions). However, there are a few factors that can cause the fob to cease functioning. G28 Car Keys includes a dead coin battery or water damage buttons, worn ones and a receiver module issue and signal interference or a malfunctioning electronic chip. If the fob is in an area that has experienced severe trauma (such as being dropped onto a hard floor or being washed in the washing machine) the fob may not be able to connect with the Body Control Module (BCM) of the car. This is because the BCM is secured and will only accept a signal from a genuine key and not any other. You'll need to replace the fob in case this happens. A professional locksmith can handle the entire process of replacing your key including programming a new key for your 500. They can even offer the fob cloned to work just like the original (and costs only a fraction of the cost).